ECUTalk v1.3.3 を使ってみた

2008/5/12 にv1.3.3のダウンロードが可能になったので更新しました。

Features/fixed bugs in v1.3.3 final (from 1.3.3 beta4):
#42 Removed console output for few users who have a console setup on their PPC
#55 Trip meter sensors shouldn't keep 'counting' while car is turned off
#58 Prevent 'clicking' show gauges button with keyboard when gauges already shown
#69 PPC users can now utilise the 'working area' option and the LTRB option (ini setting)
#70 Changed default 100ms max refresh to 40ms (equivalent of 25fps)

Features/fixed bugs in beta4 and previous (from 1.3.2):
#10 Put font size/scaling for gauges in options
#31 When value exceeds gauge maximum, the actual value should be on digital readout
#32 When you read fault codes without having connected to ecu, ecutalk exits
#33 Gauge colour preview doesnt update till you restart ECUTalk
#35 Save long term trip sensor statistics
#36 Clear trip statistics from sensors
#37 Option dropdown lists are editable on laptop/PC (shouldn't be)
#38 check for port open when reconnecting when gauges showing
#39 Put option in for data flush wait time
#41 If using L|T|R|B settings in the ini file, the gauges arent displayed properly if L is far from 0.
#1 Automatically attempt reconnection to ECU after connection lost
#5 Other Trip Meter Sensors (Fuel Used, Trip Fuel Economy, Trip Distance)
#14 Add offset option timing so US users can get correct timing readings
#22 imperial (etc) option in the options is cutoff with japanese font
#24 Derived sensors should select dependent sensors automatically
#25 Options might not be saved if you dont select another tab before closing
#26 Priority option for ECUTalk (eg so mp3 etc play fine)

2007/8/21 にv1.3.3 beta4のダウンロードが可能になったので更新しました。

New features/fixed bugs in beta4 below:
#10 Put font size/scaling for gauges in options
#31 When value exceeds gauge maximum, the actual value should be on digital readout
#32 When you read fault codes without having connected to ecu, ecutalk exits
#33 Gauge colour preview doesnt update till you restart ECUTalk
#35 Save long term trip sensor statistics
#36 Clear trip statistics from sensors
#37 Option dropdown lists are editable on laptop/PC (shouldn't be)
#38 check for port open when reconnecting when gauges showing
#39 Put option in for data flush wait time
#41 If using L|T|R|B settings in the ini file, the gauges arent displayed properly if L is far from 0.

Additional notes:
1) For Flush Wait option, 100ms is default, lower values will give quicker startup times, but higher values might help with some connection problems, eg sensors not showing up, ECU part number not being read, gauges not moving when showing gauges, etc. Eg I can use 20ms on my desktop and 50ms on my 568 Jornada.
2) For Font Base Size and Increment, this allows you to specify a font size, and then the amount of pixels which the font size will be incremeneted depending on gauge size. Eg 6pt + 50px increment on a 200px wide gauge = 10pt font.
3) Also a minor fix to heading names in logs so distance/fuel used have units (KM/Mi,L/Gal)

2007/8/13 にv1.3.3 beta3のダウンロードが可能になりました。
β版という事で新機能について評価をしてくださいということです。

Features/fixed bugs in beta3 and previous:
#1 Automatically attempt reconnection to ECU after connection lost
#5 Other Trip Meter Sensors (Fuel Used, Trip Fuel Economy, Trip Distance)
#14 Add offset option timing so US users can get correct timing readings
#22 imperial (etc) option in the options is cutoff with japanese font
#24 Derived sensors should select dependent sensors automatically
#25 Options might not be saved if you dont select another tab before closing
#26 Priority option for ECUTalk (eg so mp3 etc play fine)

動作確認PC
SHARP MURAMASA PC-MT1-L2
Windows XP HOME Edition SP2
CPUはIntel SpeedStepテクノロジ対応超低電圧版モバイルPentium IIIプロセッサ600MHz
（バッテリーのみで動作させているため 300MHz固定動作）メインメモリは192MB
通信ポートは秋月電子通商で販売しているUSB-シリアル変換を使用しCOM4で設定